Radiation Safety. Amplified.
Join us on Linkedin
Follow us on YouTube
Subscribe to our Blog

CANBERRA Product Software and Firmware Updates

If you have contacted us and received your user name and password, please login in the area below.

If you have forgotten your login, need a login or have any questions regarding your software or the availability of updates for your software, please contact our support team at: techsupport@canberra.com.

Once inside you can select the appropriate download. You may be prompted for your login and password again.

User Name :Password :

Please look at the list of available software updates below to see if there is an update available for your CANBERRA software.

Click a Software title to view the details of the Software Update.

AIM/SNAP6 64-bit Genie 2000 V3.3 Device Driver - Release Date: 11/08/2013

Details:

Provides support for the AIM on Genie 2000 Version 3.3 for Windows 7 64-bit Operating Systems and Windows Server 2008 R2.

Note:

This release of the AIM SNAP Protocol Driver (NDIS 6.0) has been tested with Windows 7 x64 and Windows-2008 R2 using Genie 2000 Version 3.3 and verified up to and including 16 inputs.  For Windows 7 x86 and Windows XP operating Systems, the SNAP Protocol Driver NDIS 5.0 should be used.

If you reinstall Genie 2000 you may need to reinstall the SNAP Protocol Driver. The Genie 2000 installation may overwrite the AMSNAP32.dll file required by the SNAP Protocol Driver with an earlier version of the file.

Version 3.3 of the Genie 2000 installation does not copy the AIM driver data files when installing on 64 bit operating systems. These files, AIMMCA64.DRD, DSP_DEV.DRD, ICB_DEV.DRD, MANUAL.DRD and PARALLEL.DRD are provided on the SNAP driver installation disk and must be copied manually. The location for these files is the "C:\GENIE2K\DRIVERS\"; where "C:" would be replaced by the drive letter of the disk where Genie 2000 was installed. With these files in place you will be able to define AIM inputs using the Genie 2000 MCA Input Definition Editor.

Installation:

  1. Open the "Network and Sharing Center" using the Control Panel application. Click on "Change adapter setting" in the upper left corner. Right click on the "Local Area Connection" icon and select "Properties".
  2. Click on "Install..." to bring up the "Select Network Feature Type" dialog.
  3. Select "Protocol" and click "Add..." to bring up the "Select Network Protocol" dialog.
  4. Click "Have Disk..." to bring up the "Install From Disk" dialog.
  5. Click "Browse..." and find the directory with the AimSnap6.inf file, select the file and click "Open", "OK", "OK".
  6. Once the driver has loaded you will see "Canberra NDIS 6.0 SNAP Protocol Driver 1.0" in the list box.
  7. Reboot the system to complete the driver installation.

Downloads

To download this update, please login at the top of the page.

Apex-Gamma V1.4:  SPR Notice M3555580 - Release Date: 12/2/2015

Details:

Provides support for ISOCS Well Detector Characterizations to be installed and used with Apex-Gamma V1.4. This enables cascade summing corrections for the germanium well detector and (if S574 LabSOCS or S574 ISOCS is installed) ISOCS/LabSOCS mathematical efficiency calibrations in Apex-Gamma for well detectors. The following prerequisites are required for this patch:

  • S500/S502/S504 Genie 2000 Basic Spectroscopy V3.4
  • S501 Genie 2000 Gamma Analysis V3.4
  • Apex-Gamma V1.4
  • Custom ISOCS Detector characterization (Model ISOXCAL) for a Germanium Well detector

Caution:

These patch files have been engineering tested only. They have not been formally verified and validated through a formal QA process. Users should exercise caution when using these patch files.

Installation:

  1. Confirm that the Genie, ISOCS, and Apex-Gamma applications are not running.
  2. Navigate to the following directory and rename the two files SocsAccess.dll and SocsHlpr.dll to create a backup:
    • Rename
      “C:\Genie2k\ISOCS\ExeFiles\SocsAccess.dll” to
      “C:\Genie2k\ISOCS\ExeFiles\SocsAccess_orig.dll”
    • Rename
      “C:\Genie2k\ISOCS\ExeFiles\SocsHlpr.dll” to
      “C:\Genie2k\ISOCS\ExeFiles\SocsHlpr_orig.dll”
  3. 3. Download the file SPR M3555580_{Language}.zip for you desired language and then extract the files SocsAccess.dll and SocsHlper.dll to a temporary location. These can be identified by File Version 4.4.0.2941
  4. Place these files into the same location as above: C:\Genie2k\ISOCS\ExeFiles\
  5. Launch an elevated command prompt (run as Admin).
  6. Register the file SocsHlpr.dll using the 32-bit version of Regsvr32.exe as follows:
    • Type “cd C:\genie2k\isocs\exefiles"
    • For Windows 7 32-bit, type “%windir%\system32\regsvr32 SOCSHlpr.dll”
    • For Windows 7 64-bit, type “%windir%\SysWoW64\regsvr32 SOCSHlpr.dll”
  7. If using Apex-Gamma Client/Server, repeat for each Apex-Gamma client and the Apex-Gamma Server on the network.

Downloads

To download this update, please login at the top of the page.

Avior 2000 / MIP10 Digital    Revision: E1.11 - 01/31/2015

New Features

  • New probe management:
    • SABG-30B
    • SN-D

Comments:

New version for SABG-30B and SN-D

Known Issues:

  • N/A

Downloads

To download this update, please login at the top of the page.

Avior 4000     Revision: U1.11 - 01/31/2015

New Features

  • New probe management:
    • SABG-30B
    • SN-D

Comments:

New version for SABG-30B and SN-D

Known Issues:

  • N/A

Downloads

To download this update, please login at the top of the page.

COLIBRI     Revision: V3.2 - 06/27/2017 - (FOR COLIBRI v1.1 ONLY)

Comments:

This document describes the changes between versions of Colibri and any known issues. For the latest news on Colibri, visit the Canberra web site at www.canberra.com.

NOTE:

Upgrading from Version 3.1 only requires Nk.bn0 and CompressedCabFile_V3_2_Coll11.CAB to be used.

New Features:

  • Quality check uses c/s for SI unit, and in dpmeq for US unit
  • Internal data log can be disabled

Fixed Issues:

  • Colibri get stuck during the log off and log on process

Known Isuues:

  • Some Russian words translation is missing.
  • Loosing sound when Bluetooth Headset is out of range or turned off when connected
  • In manage user profile file menu Upload functionality doesn’t work

Compatibility:

This version is compatible only with Colibri hardware V1.1. Look for the Colibri identification label. V1.1 must follow the part number. And this new hardware is not compatible with the previous versions.

  • This version is compatible with06/02/2017 nk.bn0 image
  • This version is compatible with 2.13 PIC version.
  • This version is compatible with 3.00 PIC bootloader version.
  • This version is compatible with 1.30 gauge firmware version.

Downloads

To download this update, please login at the top of the page.

COLIBRI     Win7 & 8 Driver - 10/15/2013

Comments:

This driver is compatible with Windows 7 and Windows 8 for Colibri-TTC and Colibri-VLD all versions. You must install first the driver before you connect Colibri to the computer.

Revision Changes / Additions:

  • New driver

Downloads

To download this update, please login at the top of the page.

CP5 Plus Firmware Update - 12/15/2015

New Functions:

  • The firmware in the CP5-PLUS controller will be able to detector whether it is connected to a CP-5 or CP5-PLUS coldhead.
  • During startup the controller detects the coldhead version and automatically selects the applicable wire compensation.
  • Both parameters can be modified through the serial interface, using the “factory” login mode.
  • Only the original wire compensation parameter is adjustable through the “CP-5 control panel” software, again using “factory” login.
  • Default setpoint for HV-inhibit will be -170°C.

Downloads

To download this update, please login at the top of the page.

CSP - Multiple Probes     Revision: 91629_A_V-2011-01-24 - 02/28/2011

Comments:

Follow CSPS user manual upgrade procedure to load new firmware into CSP probe of interest.

This document describes the changes between previous firmware version and any known issues.

FIRMWARE PART NUMBER: 91629-A
RELEASED VERSION: 91629_A_V-2011-01-24.HEX
PREVIOUS VERSION: V-2010-11-03.HEX

PRODUCTS IMPACTED:
· SA20 probe P/N: EM75270
· SA20-2 probe P/N: EM90062
· SA32 probe P/N: EM90666
· SB20 probe P/N: EM74672
· SAB100 probe P/N: EM75864
· SABG100 probe P/N: EM81833
· SA100 probe P/N: EM75863
· SB100/A probe P/N: EM75862
· SB100/B probe P/N: EM82069
· SG1-R probe P/N: EM75860
· SG2-R-A probe P/N: EM75861
· SX2-R-A probe P/N: EM78677
· SPAB15 probe P/N:EM78766

New Features:

  • None

Known Isuues:

  • HV failure not active for SPAB15 probe
  • The status bit 5, power supply failure, is not functional.

Fixed:

  • SG1-R and SG2-R probes can show a sporadic saturation due to a timing conflict between the analog to digital conversions made in the probe
  • The initialization time is now set to 30s instead of 20s. 20s was too short to cover the necessary stabilization time of some SG2-R probe
  • The period of FRAM integrity check is now set to 30s instead of 20s. Because it is
    synchronized with the initialization bit

Compatibility:

  • Need a CSPS version higher than V2.00B to uses the 'firmware update' and 'writing
    defaults parameters' functions
  • Need a Radiagem firmware version higher than V2.19

Downloads

To download this update, please login at the top of the page.

CSP COM     Revision: 3.01 - 1/05/2015

Comments:

Follow the procedure in the attached documents.

Note:

  • CSPS V3.01 required for this update.

Downloads

Right-click and choose "save target as" to download the file to your computer.

To download this update, please login at the top of the page.

DSA-1000 and Inspector-2000 64-bit Genie V3.3 Device Drivers - Release Date: 09/30/2013

Details:

Provides support for the DSA-1000 & InSpector 2000 MCAs with Genie 2000 v3.3 on Windows 7 64-bit operating systems. The following are updated:

  • The CIUSB kernel driver updated for Windows 7 64-bit support. The version of this driver is v2.71.
  • The I2KUSB32.DLL protocol driver updated.
  • DSA-1000 and InSpector 2000 .drd driver file location updated.

Note:

This driver is fully qualified with Genie 2000 v3.3 under Windows XP SP3, Windows 7 SP1 32-bit, Windows 7 SP1 and Windows-2008 R2 64-bit operating systems and under English, French, German, and Russian installations.

Installation:

  1. Run a command prompt (cmd) as an administrator.
  2. Navigate to the installation media.
  3. Execute install.bat.
  4. After completion, restart the computer (even if not prompted).

Downloads:

To download this update, please login at the top of the page.

Genie 2000 Panolin Update: SPR Notice J4324940 - Release Date: 7/15/2017

Comments:

This update is for peak fitting when applied to significantly large regions of interest. Specifically, this update will improve the Genie 2000 Sum / Non-Linear LSQ Fit peak area routine for regions of interest that are approximately 12 times or greater the full width at half maximum (FWHM) of a representative peak in the region. This typically occurs only for very complex spectra when a high density of nuclide peaks are generated.

Please Note:

Please note: This update is a fully qualified patch for Genie 2000. Updating this patch may affect nuclide results for Genie 2000 and layered applications, for example Apex-Gamma and NDA 2000.

Downloads:

To download this update, please login at the top of the page.

Installation:

  1. Review the version of Genie 2000 that is installed. 
  2. If using Genie 2000 Version 3.4.1, download the file download the file SPR_J4324940_V341_{Language}.zip for you desired language and then extract the file Panolin.dll to a temporary location. These can be identified by the File Version 3.4.1.3009 and Date Modified value of 13-Jun-2017.
  3. If using Genie 2000 Version V3.2.1, V3.3, or V3.4, download the file SPR_J4324940_V321-34_{Language}.zip for you desired language and then extract the file Panolin.dll to a temporary location. These can be identified by the Date Modified value of 13-Jun-2017.
  4. Confirm that the Genie 2000 and related applications are not running.
  5. Navigate to the ExeFiles folder of the base Genie installation and rename the file “Panolin.dll” to create a backup.  For example, rename  “C:\Genie2k\ExeFiles\Panolin.dll” to “C:\Genie2k\ExeFiles\Panolin_orig.dll”
  6. Place the downloaded and extracted file into the same location as above: C:\Genie2k\ExeFiles\
  7. Restart Genie 2000 and/or related applications.

Health Physics Contamination Monitor Software Version: 9.01.2–November 1, 2016

Comments:

This is a compressed ZIP file containing Monitor software Version 9.01.2 installation files, installation instructions and changes information related to the following:

Applicable Usage:

  • Serial Bus Contamination Monitors (SOFT-MON-SERIAL):
    • Argos-3AB, Argos-5AB, Argos-3PB, Argos-5PB, Argos-3PAB, Argos-5PAB, Argos-3PBG and Argos-5PBG, Personnel Monitors:  Standard Computer Box SCN:814380 or 7079641
    • Sirius-5AB, Sirius-5PB,Sirius-5PAB and Sirius-5PBG Personnel Monitors:   Standard Computer Box SCN:814380 or 7079641
    • Cronos-1, Cronos-4, Cronos-11 Gamma Object/Tool Monitors:    Standard Computer Box SCN:814380 or 7079641
    • GEM-5, GEM-5W, Personnel Monitors: GEM-5 Computer Box SCN:814410 or 7079642

Related Products Supported by Monitor Version 9.01.2 (161101):

  • SOFT-CREMOTE (and 7062263) REMOTE CONTROL DATA ACCESS LAN SW Version 1.07 (131114)
  • SOFT-LDB Loc.Database Support;Factory Installed
  • SOFT-LDB-KIT Loc.Database Support;Field Install. Kit
  • SOFT-LDB-KITPC-A Loc.Datab.Supp.;Field Inst.Kit w/PC;Arg5
  • SOFT-LDB-KITPC-G Loc.Datab.Supp.;Field Inst.Kit w/PC;GEM5

Related Products NOT Supported by Monitor Version 9.01.2 (161101):

  • SOFT-CREMOTE (and 7062263) REMOTE CONTROL DATA ACCESS LAN SW Version 1.06.4 (130627) and earlier
  • SOFT-CHISTORY CHISTORY LAN SW Version 2.11 (080908) and earlier
  • SOFT-CMONITOR CMONITOR LAN SW Version 2.11 (080908) and earlier
  • Parallel Bus Contamination Monitors (SOFT-MONITOR):
    • Sirius-2, Sirius-4, Argos-2, Argos-4 Personnel Monitors:   Standard Computer Box SCN:814370
    • GEM-5P Personnel Monitors:   GEM-5 Computer Box SCN: 814360

Revision Changes / Additions / Fixes:

To download this update, please login at the top of the page.

Downloads


To download this update, please login at the top of the page.

InSpector™ 1000 v1.5.3 - Release Date: 07/17/2013

Introduction:

Thank you for purchasing the InSpector 1000 Digital Handheld MCA. This CD contains the following software and documentation (Note: only the front-end of the installer has changed since version 1.5.2)

Release V1.5.3

Support installation on Windows 7 64-bit. The Windows 7 32-bit or 64-bit version of Windows Mobile Device Center V6.1 (or ActiveSync 4.2 for machines running XP) will launch when selected from the main installation menu, depending on the Operation System.

Installation:

  1. To start the installation, select ‘Start’, then ‘Run’, then ‘Browse’.
  2. Now select your CD-ROM/DVD drive, for instance [E:], double click on ‘Setup.exe’, then click on ‘OK’.
  3. Follow the on-screen instructions to install the software and its documentation.

Downloads:

To download this update, please login at the top of the page.

Lynx MCA    Revision: 1.3.1.x – 10/1/2014

New Features:

  • Following features have been added to the Lynx MCA
    • The traditional Java-dependent web interface has been replaced with an application based on Adobe Flash technology. This application requires browser support for Adobe Flash Player 10.2 or greater. Internet Explorer and Firefox require a specific plug-in supplied on the CD; Chrome natively supports Adobe Flash, therefore no plug-in is required. The traditional Java-dependent interface and pure HTML interface have been retained but are accessible through different URL. Please refer to the Lynx Web Client User's Manual.pdf included in the CD for additional information on accessing the Lynx
    • Advanced coincidence logic has been added to provide more flexibility when performing coincidence gating. Please refer to the Acquisition Settings section in the Lynx User’s Manual
    • Manual mode and threshold settings have been added to increase the sensitivity of low-energy signals. Please refer to the Low-Energy Applications section in the Lynx User’s Manual
    • Spectral data collected using MSS, LIST and TLIST are not automatically stored from the web page. Secondary programs (e.g., Prospect) should be used for these configurations.
    • Flash-based user interface uses Operating system locale settings for formatting numbers (for example decimal symbols and digit grouping symbol). It will support only following formats correctly: Chinese, Danish, Dutch, English, Finnish, French, German, Italian, Japanese, Korean, Norwegian Bokmål, Portuguese, Russian, Spanish and Swedish.

Fixed:

Below is a list of the various problems that have been resolved:

  • High Voltage Inhibit control now defaults to ‘Enabled’ in V1.3
  • The resolution of the Gate Delay setting has been increased from 10.0 uSec to 0.1 uSec

Upgrading from previous versions to V1.3.1.x

There are two methods to update your Lynx from V1.2 or earlier, to V1.3.1.x

  1. Update via the Web Browser (Preferred Method). Updating to V1.3.1.x via the Web browser consists of a two-step process, as outlined in the Updating Lynx Firmware from V1.2 to V1.3 for the first time section of the Lynx User’s Manual included in the CD. This procedure requires that the Lynx is fully operational and proper Java compatibility exists between PC and Lynx; if both conditions do not exist, then the update must be performed using the Boot loader method.
  2. Update via the Boot loader. Updating to any version via the Boot loader is always a single step process. This procedure can be used anytime, even to restore a non-responsive Lynx. The Boot loader update method is outlined in

The new Lynx operating software, V1.3.1.x, is located on the Lynx Utility Software CD.

Version information can be determined through the web page’s System link. For Lynx V1.3.x.x the Mca Version field will report 1.3.1.x; V1.2 or earlier will report V1.2.x.x or V1.1.x.x.

Notes:

Hardware settings will be lost when upgrading from previous versions to V1.2 or earlier. If you wish to preserve the settings, perform a backup. Restore the backed up settings after upgrading.

Additionally, be sure that all acquisitions have been turned off before performing the update. During the update the device will reset; all communication and acquisition activities will be aborted. If acquisition was active for SCA's, Counters, List/TList, or MSS, any data in the internal acquisition buffers will be lost once the device resets.

Downloads

To download this update, please login at the top of the page.

MiniSentry     Revision: 2.02 – 01/31/2006

Comments:

This is a compressed ZIP file containing MiniSentryWin.exe Version 2.4, MiniSentry Firmware Version 2.02

MiniSentryWin.exe Version 2.4 (June 1, 2011):

  • Revision Changes / Additions:
    • Cosmetic change to show MiniSentry logo
    • Support for USB TO RS232 SERIAL ADAPTER CABLE (such as CANBERRA Co. SCN 7072489)
  • Fixed:
    • Fixed grey-out logic for Printer button.

MiniSentry Firmware Version 2.02 (January 31, 2006):

  • Revision Changes / Additions:
    • Support for surface-mount main board and dual input boards (is backwards compatible with through-hole boards).Support for USB TO RS232 SERIAL ADAPTER CABLE (such as CANBERRA Co. SCN 7072489)

Downloads

To download this update, please login at the top of the page.

Multiport II USB 64-bit Genie V3.3 Device Driver - Release Date: 10/30/2013

Details:

Provides the Multiport II USB Genie 2000 driver for support on Windows 7 64-bit Operating Systems and Windows Server 2008 R2. This driver is compatible with Genie 2000 Version 3.3.

Note:

This release of the Multiport II USB driver (Version 1.0.0.3) has been tested with Windows 7 x64 and Windows 2008 R2 using Genie 2000 Version 3.3. For Windows 7 x86 and Windows XP operating Systems, the Multiport II Version 1.0.0.2 USB Driver should be used.

Version 3.3 of the Genie 2000 installation does not copy the Multiport II driver data files when installing on 64-bit operating systems. These files, DrMp2.DRD, MANUAL.DRD and PARALLEL.DRD are provided on the Multiport II driver installation disk and must be copied manually. The location for these files is the "C:\GENIE2K\DRIVERS\"; where "C:" would be replaced by the drive letter of the disk where Genie 2000 was installed. With these files in place you will be able to define Multiport II inputs using the Genie 2000 MCA Input Definition Editor.

Additionally the Genie 2000 installation does not create required registry entries for the Multiport II. The file MP2.reg is provided on the driver installation disk to create the required registry entries. Right click on the MP2.reg file and select the Merge operation to update the registry. Answer affirmatively to messages asking you if you really want to perform this update.

Installation:

  1. Connect the Multiport II USB output to your computer.
  2. Open the "Device Manager" using the Control Panel application.
  3. Look for "Canberra - Multiport II" in the Device Manager window. It will be listed under "Other devices".
  4. Right click "Canberra - Multiport II" and select "Update Driver Software...".
  5. Click on "Browse my computer for driver software" and then browse to the directory containing the MPort2.inf file. Click "Next" to begin the installation.
  6. A Windows Security dialog will appear saying that "Windows can't verify the publisher of this software". Click on "Install this driver software anyway".
  7. The driver installation will complete in a few minutes. You may be asked to reboot the computer before the driver can be used.

Downloads

To download this update, please login at the top of the page.

Osprey V1.0.4 Firmware - Release Date: 6/27/2014

Details:

This document provides information regarding the latest software and firmware release for the OSPREY MCA.

Major changes and bug fixes:

  • Incorporated a new default web configuration and status page, while maintaining backwards compatibility with the existing web page.
  • SPR C4116350 - Osprey Mass Storage can become corrupted resulting in device being un-usable
  • SPR C2361409 - BLR set to wrong value when dead time is between 50%-62%
  • SPR C9208285 - Device may crash if a requested parameter list includes a string parameter and elapsed time
  • SPR C3861219 - Exception handler added to allow device recovery from lockup
  • SPR C10119410 - Spectrum reconstruction affects List/TList performance
  • SPR C8763942 - Device may lock up during asynchronous GetSpectrum requests
  • SPR C2430991 - Error when GPIO Functions #22 and #27-29 selected
  • SPR V9732585 - AUX CNTR in Manual Dependent mode produce no data records

Installation:

  1. Install the USB drivers before connecting the OSPREY to the host computer. The installation is described in the user manual under Installing the USB Driver section.
  2. Driver installation is only required for Windows based systems.
  3. V1.0.4 Osprey firmware is compatible with all Osprey MCAs shipped prior to this release. Refer to the Osprey User's documentation for instructions updating your device.

Miscellaneous changes bug fixes and enhancements:

  • Parameters not supported by the Osprey will return UNSUPPORTED code for both Meta and parameter query.
  • Improved TCP/IP and USB stack for asynchronous messages.
  • Heap extended to 8 Mb since the hardware already supports 8 Mb.
  • Added default initialization values for Input_RoiUncMult and Input_RoiNumBkgChans parameters.
  • Fixed race condition between a voltage change and "ramping" status returned by device.
  • Added RevB to RevD hdw transition along with associated FPGA and firmware support Page 2 of 7
  • Fixed meta data return for DigitalOffset and DSO parameters for compatibility with new web configuration page.
  • Ported USB changes from DSA-LX for timeout, address assignment, and handling of multiple devices.
  • Fixed occasional device crash during stream operation.
  • Fixed occasional device crash when client closes.
  • Added dynamic support for AT43DB641/642 NAND flash devices.
  • Fixed occasional crash when device retrieves default value for MACs and Serial Number parameters
  • Fixed problem with LED not blinking red and fault not asserted if the fpga configuration file isn't found
  • PutSpectrum now returns error when in List, TList, or MSS mode

Downloads

To download this update, please login at the top of the page.

omniTrak     Revision: 5.03 - 07/03/2009

Comments:

This is a self-extracting installation file containing omniWin.exe version 5.3, omniTrak Firmware version 5.06, help files and manuals

Revision Changes / Additions:

  • OmniWin version 5.03 (06/12/11) Release Notes.

Fixed:

  • Fixed problem of not properly recognizing a dual input omniTrak.

Downloads

To download this update, please login at the top of the page.

Radiagem 2000     Revision: V2.28 - 01/31/2015

CAUTION

This release IS NOT SUPPORTED by some old Radiagem 2000 / Radiagem 4000.

Please refer to the Release Notes (in zip file below) to verify that your radigem 2000/4000 is eligiable for this revision.

Downloads

To download this update, please login at the top of the page.

New Features:

  • New probe management:
    • SABG-30B
    • SN-D

Known Issues:

N/A

Comments:

New version for SABG-30B and SN-D

Radiagem 4000     Revision: V4.28 - 01/31/2015

CAUTION

This release IS NOT SUPPORTED by some old Radiagem 2000 / Radiagem 4000.

Please refer to the Release Notes (in zip file below) to verify that your radigem 2000/4000 is eligiable for this revision.

Downloads

To download this update, please login at the top of the page.

New Features:

  • New probe management:
    • SABG-30B
    • SN-D

Known Issues:

N/A

Comments:

New version for SABG-30B and SN-D

S900C     Revision: 2.0.4 - 06/08/2011

Comments:

UltraRadiac and UltraRadiac-Plus Setup software - S900C: setup.exe

Run setup.exe to install the URad+ Setup application.

It's default directory will be C:\Program Files\URadPlus Setup\

It will install/copy the following:

  • s900cu.exe - the application executable
  • s900cu.ini - holds some program configuration data
  • s900cu.xml - stores the saved templates
  • s900cuempty.xml - original (empty) templates file
  • mingwm10.dll - support DLL (Dynamic Link Library)
  • SiUSBXp.dll - support DLL
  • unins000.dat - file(s) for un-installation
  • unins000.exe

Note that the program user will need read/write access to the files in the installation directory. Otherwise configuration data (such as COM port settings) and parameter templates will not be saved.

ACTiSYS Infrared Adapter
------------------------

An UltraRadiac/URad+ device communicates with a PC via its IR (Infrared) port. The necessary ACTiSYS IR adapter is supplied with the Setup Software.

There are two types of ACTiSYS adapters:

1) Serial(RS232)<->IR adapter, typical part# ACT-IR220LN9.6, connects to a PC's serial (COM) port. This adapter is powered from the serial port and requires NO special drivers.

2) A USB<->IR adpater, typical part# ACT-IR204UN, connects to a standard PC USB port. This adapter is powered from the USB port and REQUIRES DEVICE DRIVER(S) to operate.

For the USB<->IR ACTiSYS adapter, follow the "Driver Installation" instructions included with the adapter to install the necessary driver(s) from the included ACTiSYS CD. If properly installed (and connected) the Device Manager will show "ACT-IR204UN USB Serial IR Port (COMx)" under Ports(COM & LPT) and "ACTiSYS ACT-IR204UN USB Serial IR Adapter" under Universal Serial Bus controllers.

The Device Manager can be reached (in XP) by: Start>Control Panel>System to get to the System Properties window (alternately, right-click "My Compter" and select "Properties"). From here, click the "Hardware" tab, then click the Device Manager button.

Revision Changes / Additions:

  • Add: Log export error count added to results
  • Add: Battery type configuration added to URad115/URadPlus

Fixed:

  • IR Half-Duplex Tx to Rx delay properly implemented for URad115/URadPlus
  • Corrupted log data no longer ends log export

Downloads

To download this update, please login at the top of the page.

SN-S     Revision: SNS_20110106 - 02/18/2011

Comments:

Follow CSPS user manual upgrade procedure to load new firmware into SN-S

Fixed:

  • No variation of the High Voltage value when you plot the High Voltage plateau with CSPS software
  • No variation of the discriminator value when you plot the discriminator curve with CSPS software

Downloads

To download this update, please login at the top of the page.

STTC     Revision: 11_07_11 - 07/22/2011

Comments:

Needs CSPS software and PC cable for probe upgrade. Please refer to CSPS user manual for upgrade procedure

Revision Changes / Additions:

  • A specific firmware version does exist for the TTC module inside the Colibri product. This version is referenced 11_07_12.

Fixed:

  • Communication interruption during approximately 1s between 1mSv/h and 10mSv/h
  • Improved probe status handling
  • Improved the use of unit information in the CSP frame
  • Separate handling of range and microcontroller frequency

Downloads

To download this update, please login at the top of the page.

SVLD     Revision: VLD_20121105 - 11/05/2012

Comments:

SVLD erratic saturation bug fixture

Revision Changes / Additions:

  • A specific firmware version does exist for the TTC module inside the Colibri product. This version is referenced 11_07_12.

Fixed:

  • Counting spike of a ¼ s :
    • with erratic time intervals
    • In a stable and low dose-rate level, the SVLD probe or the COLIBRI-VLD turns into saturation for a short time before returning to normal operation.

Compatibility:

  • This version is compatible with CSPS V3.0.
  • This version is compatible with Colibri V2.6
  • This version is compatible with MIP10 Digital
  • This version is compatible with AVIOR v.1.09
  • This version is compatible with Radiagem 2000 v.2.25
  • This version is compatible with Radiagem 4000 v.4.25

CAUTION

If CSPS cannot communicate with the VLD module (SVLD or COLIBRI-VLD), you need to apply the VLD FIX to allow connection to CSPS. Please, follow each step describes in attached release note.

Downloads

To download this update, please login at the top of the page.